The 6.5×52mm Carcano, also known as the 6.5×52mm Parravicini–Carcano or 6.5×52mm Mannlicher–Carcano How to set up clock in yokatta dx-6. , is an Italian military 6.5 mm (.268 cal, actually 0.2675 inches) rimless bottle-necked rifle cartridge, developed from 1889 to 1891 and used in the Carcano 1891 rifle and many of its successors. A common synonym in American gun literature is '6.5mm Italian.' In American parlance, 'Carcano' is frequently added to better distinguish it from the rimmed hunting cartridge 6.5×52mmR (U.S. Diablo 2 torrent espanol. version: .25-35 Winchester). Ballistically, its performance is very similar to that of the 6.5×54mm Mannlicher–Schönauer.
Vcarve 6.5 Modeling Tab Review
(Redirected from 6.5x52mm Mannlicher-Carcano)
Design[edit]
Under the direction of the Commissione delle Armi Portatili (commission for portable weapons), instituted in 1888, to develop a smokeless-powder rifle for the Italian Army, the Reale Laboratorio Pirotecnico di Bologna (royal pyrotechnical laboratory of Bologna) developed and tried several different cartridge designs, with bullet diameters from 6 to 8mm. Finally, due also to the influence of Major Antonio Benedetti of the Brescia Arsenal, secretary of the commission and strong supporter of the advantages of smallbore cartridges, the 6.5×52 cartridge was adopted in March, 1890, prior to the adoption of the rifle that used it (the Model 1891 Carcano rifle).
Italian 6.5mm Carcano military cartridge, cut in half
After the adoption of the cartridge, the arsenal's technicians worried about the characteristics of the original ballistite load, since that propellant was considered too erosive (flame temperature of 3,000-3,500 °C) and not stable under severe climatic conditions. Several other loads were tested, including the British cordite, but without good results, until the Reale Polverificio del Liri (royal explosives factory of Liri) developed a new propellant called 'Solenite,' composed of trinitrocellulose (40%), dinitrocellulose (21%), nitroglycerine (36%) and mineral oil (3%), and shaped in large tube-like grains. The new propellant, that reduced the flame temperatures to 2,600 °C and proved to be very stable, and was adopted in 1896 and never changed until the end of the military production of the cartridge.
The 6.5×52mm Carcano was designed as an infantry cartridge. In accordance with the tactics of the time, the adjustable rear sight of the rifle allowed for volley fire up to 2,000 metres. The 6.5×52mm Carcano was the first to be officially adopted of a class of similar smallbore military rifle cartridges which included the 6.5×50mm Arisaka (Japan), 6.5×53mmR Mannlicher (Romania/Netherlands), 6.5×54mm Mannlicher–Schönauer (Greece), 6.5×55mmSwedish Mauser (also Norwegian Krag–Jørgensen), and the Portuguese 6.5×58mm Vergueiro.
(Left to right) 8mm Mauser (also called 7.92mm Mauser), 6.5mm Carcano, and 7.35mm Carcano
A comparison with larger-bore smokeless powder cartridges of the 7 and 8 mm calibre class (such as the French 8×50mmR Lebel, the German 7.92×57mm, the Austrian 8×50mmR Mannlicher, the .303 British, the Russian 7.62×54mmR, the Belgian and 7.65×53mm Argentine, the American .30-40 Krag, and the much later .30-03 and .30-06 Springfield) may make the 6.5mm rounds appear underpowered on paper, and lacking in stopping power. However, the small bore cartridges have a long list of advantages, such as flatness of trajectory, outstanding penetration at distance, less weight, less recoil, smaller dimensions, and less material required in production.
Its short-lived intended successor cartridge, the 7.35×51mm Carcano, was designed to replace the 6.5mm Carcano, but those plans were cancelled due to the logistic difficulties that arose once World War II commenced.
The original 6.5×52mm barrel design, developed by the Brescia Arsenal at the same time as the cartridge before development of the M91 Carcano rifle itself, used a gain twist barrel with deep rifling to reduce wear and give consistent accuracy. A gain twist has a slow initial twist in the barrel, progressively getting faster until the final twist rate is attained near the muzzle, resulting in less torque being imparted to the bullet during the highest stress phase of the interior ballistic cycle, and thus less wear in the throat of the barrel. Gain twist was phased out in the last production of the Carcano rifle in favour of conventional rifling.
A 6.5×52mm Carcano cartridge loaded with a modern hunting bullet
Performance[edit]
With properly bulleted ammunition, the 6.5×52mm Carcano is an effective deer cartridge up to about 200m (220 yards).[citation needed] However, the standard Italian service round used an unstable round-nosed bullet with a propensity to tumble, whether hitting soft tissue/ballistic gel or harder material such as bone.
The currently available factory ammunition may lack accuracy due to the use of a 6.7mm (.264 in) bullet instead of the 6.8mm (.268 in) as originally loaded.[citation needed]
A new window named Keyboard Properties pops open. Repeated sign on keybarod. Under the Speed tab, look for a speed slider by the name Repeat delay. If you drag the slider to Long, then there will be a long delay between the first and second characters when you keep pressing a key to type in something.STEP 3.
A six-round en-bloc clip
In the JFK Assassination[edit]
The cartridge was identified by the Warren Commission as the round used in a World War II-surplus Italian 1891 Carcano (Fucile di Fanteria Mod. 91/38) rifle purchased by Lee Harvey Oswald and used in the assassination of President John F. Kennedy.
Vcarve 6.5 Modeling Tab For BeginnersSee also[edit]References[edit]
External links[edit]
Retrieved from 'https://en.wikipedia.org/w/index.php?title=6.5×52mm_Carcano&oldid=872720915'
From Vectric:
Vcarve 6.5 Modeling Table
VCarve Pro is a flexible industrial strength software package that includes all the design, layout and machining functionality demanded by commercial shops and users, while remaining incredibly easy to use and affordably priced. VCarve Pro is a complete solution For CNC routing, sign making, woodcarving and engraving. It features true shape nesting maximizes material usage minimizing waste, text editing and engraving fonts, wrapped 4 axis rotary machining, multi-color Toolpath preview, V-Carving / 3D Engrave, raised 3D prism machining, and pocketing with option for 2 cutters.
What do you need to know about free software?
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |